溶解式晾干機

◆企業產品性能 Product features

※具備有不穩定性一致性的撒氣各種壓力和露點

1.過濾塔之髙度與直徑不低于經檢測但是高精密計算出來，塔床發展阻力小，保護了再壓縮混合氣體常溫、干燥劑5秒的使用時候，充分滿足樣品氣的露點規范。

2.30％的干躁劑空間，適用于應對干躁劑的自然規律衰老，確保干躁。

3.巨型發展器，保證 熱空氣勻稱在干熱劑層，削除溝流狀況。

※粉碎氣量衰減不低于14％

1.有遠見的機筒來設計，保護100％的粘附脂肪含量，保存的脂肪含量使用增長重復利用時候的重復利用氣溫度表，提供主設備的解吸性能，會讓重復利用更根除。

2.吹干和復蘇采用了選擇性對流傳熱設計，濕大氣流淌干的物理吸附劑時效性果最合適。復蘇氣用于出口含濕量操控在亞過剩的狀態，使消音器原理器及改裝排氣管過道無返潮之慮。

3.可只能根據晾干機的電腦運行載荷所需調低可再生能力利用氣劑量，切實保障可再生能力利用熱空氣連續不斷維持，可再生能力利用壓低至臨界值。

※非常干燥劑在使用年限長

1.合理的機筒盡寸，使氣體用非常干燥的劑層的空氣流速和精力恢復好的感覺，積極主動發揮出非常干燥的劑的功能。

2.合情合理的體系運行環境，在空氣步入機筒前，經除油處理及早去除空氣中內含油量物與重危害物，避免出現缺水劑層受危害。

※生產設備采用了了新創意高的品質電動及氣動式閥和可以信賴的全電子器材可語言編程序保持器，電腦介面和諧，一鍵維持體現 雙塔生產，不斷循環時期場地可編，出廠合格證確定10min。銅閥壽命短過去了50萬次瑜伽動作。

※壓力容器封頭側壁作冷熱浸鍍鋅防生銹正確處理，10年不上銹。

※運動準確的、能穩定性、運營簡易，安轉不需要條件。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆具體技術工藝性能參數 Main technical parameters